Pepper-computer Modular Computers RS485 Bedienungsanleitung Seite 97
- Seite / 320
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SMART I/O User’s Manual
©1996 PEP Modular Computers GmbHMarch 12, 1996 Page 4 - 9
4
Chapter 4 Digital Modules
4.1.6 Configuration
Although two solder jumpers exist on the board (J1 and J2), they should
remain at their factory settings unless a user-specific filter is required that
cuts off at higher frequencies for example. If a user-specific filter is required
then contact PEP Modular Computers for further advice and refer to the
illustration shown in figure 4.1.6.1 of the filtering components.
Figure 4.1.6.1: SM-DIN1 Configurable Filter
Surface Mounted Devices (SMD) are used in the production of the SM-
DIN1 modules. The components to be changed (marked with an asterisk in
figure 4.1.6.1), need not necessarily be SMD. Refer to the Board Overview
(solder side) for the approximate position of these jumpers. It should be
noted that when calculating component values for a specific filter, the
capacitor/resistor relationship is almost linear. Therefore, it is suggested that
only the capacitor should be changed. Hence, for a doubling of filter fre-
quency input the value of the capacitor should be reduced by half.
Vcc
12
3
J1
36k
1
2
3
J2
C13 100nF
*
R1
*
HCT14
IC10
INTx
36k
- SMART I/O User’s Manual 1
- Revision History 4
- Two Years Warranty 7
- Page 0 - 10 10
- 5. Analo 11
- Table of Contents 13
- Introduction 14
- General Information 15
- Weights & Measures 16
- 1.1 Product Overview 20
- 1.2 Ordering Information 21
- 1.3 Product Information 22
- 1.4 Installation 25
- SMART-Module 27
- RJ45 Connector 28
- SMART-BASE 28
- 1.5 ISaGRAF-Installation 30
- Chapter 2 SMART-BASE 42
- 2. SMART-BASE 43
- 2.1 Specifications 44
- 2.2 Board Overview 45
- 2.3 Functional Description 46
- Interrupt 47
- 2.4 Configuration 48
- WARNING ! 49
- 2.6 ‘C’ Programming 57
- 2.7 ISaGRAF Programming 72
- 2.8 Flash Utility 77
- Table Of Contents 79
- Chapter 3 SMART-EXT 80
- 3. SMART-EXT 81
- 3.2 Board Overview 82
- 3.3 Functional Description 83
- 08 Jan. 98 91
- 4. Digital Modules 93
- Green LEDs 94
- Chapter 4 Digital Modules 100
- 4.2 SM-DOUT1 107
- Warning ! 109
- 4.3 SM-REL1 121
- Chapter 4 Digital Modules 122
- Gnd (0V) 125
- +Vcc (24V) 125
- Digital Modules 137
- 4.4 SM-ACI1 139
- WARNING! 147
- Analog Modules 157
- SMART I/O 157
- Chapter 5 Analog Modules 159
- 5. Analog Modules 163
- Red LEDs 164
- User Descriptor 164
- 5.2 SM-PT100 185
- 5.3 SM-THERM 215
- 5.4 SM-ADC1 245
- Impedance 246
- Converter 246
- 5.5 SM-DAC1 263
- 12-bit value 274
- Communications Modules 283
- 6. Communications Modules 287
- Green LED 288
- Yellow LED 288
- Transceiver 289
- Connection 291
- Interface 291
- 6.2.3 Front Panel Layout 300
- 6.2.4 Board Overview 300
- Component Side 300
- Comp. Value 301
- (24-bit) 301
- October 01, 1996 302
- Page 6- 20 302
Husqvarna 326HD60X-Series manuales
Manuales del propietario y guías del usuario para Máquinas De Jardín Husqvarna 326HD60X-Series.
Ofrecemos 1 manuales en pdf Husqvarna 326HD60X-Series para descargar gratis por tipos de documentos: Manual de usuario
Kommentare zu diesen Handbüchern